Payment & Shipping Terms:
|Certificate:||ASTM A270||Type:||WELD CLAMP|
|Tube Spec.:||ASTM A270||Surface Finish:||POLISHED|
|Steel No.:||AISI 304 TP316L||MTC:||EN10204 3.1|
ss sanitary fittings,
sanitary stainless steel pipe fittings
Stainless Steel Sanitary Fittings Valves Clamp Elbows Material 304 316
Sanitary Tri-Clamp Fittings meet ASME BPE ASTM A270
Sanitary Tri-Clamp Fittings Stocking Alloys: T304 or T316L
Sanitary Tri-Clamp Fittings Sizes: 1⁄2” – 12” OD Tube
Sanitary Tri-Clamp Fittings Sanitary Finish: 180 Grit Polish ID/OD
Sanitary Valves And Fittings 1/2'' to 4'' TP316L Stainless Steel Reducing Tee Cross Ends
All sizes of clamp end also available
ASME BPE PRODUCT SPECIFICATION
316L, chemical composition in accordance with ASTM A240
304L, 1.4404 and 1.4435 also available EN10088
According to ASME BPE-2009
Spezilla is your source for T304 or T316L Sanitary Clamp Fittings and Gaskets primarily found in the Bakery, Beverage, Cosmetic, Dairy, Food or Pharmaceutical Industries. Our Sanitary Clamp Fittings meet or exceed A270 standards with an ID polish of 180 Grit or 25 Ra on the Inside of the Tube and a 150 Grit or 32 Ra on the Outside of the tube. Sanitary Solutions stock clamp fittings that are capped, bagged and marked with the size and alloy and a heat number for full traceability for either alloy.
All types of sanitary stainless steel flow control equipment for the food & beverage, dairy, cosmetic, biotechnology, pharmaceutical, and electronic processing industries.
We also carry a wide assortment of sanitary fittings, gaskets, pumps, and valves.
Additional sizes and types are available upon request.
Valve line includes, ball, butterfly, check, seat, long stroke, mix proof, PMO, diaphragm and sampling. All valves can be supplied with a variety of actuation and control packages.
Sanitary pump line includes both centrifugal and positive displacement pumps.
Usually 1" - 4", any size is demandable
Fitting ends :
BS, DIN, SMS, A270, Weld ends, Male ends and Clamp ends
Working pressure :
* -0.9 to 10 Bar for cast body
* -0.9 to 20 Bar for forged body
Working temperature :
-10oC up to 150oC
Disk head size :
* 9.4 x 9.4mm available for cast & forged body
* 8 x 12mm, 12 x 12mm available for forged body
100% 6kgf/cm2 air or 25kgf/cm2 hydraulic and
300k times cycle test
|STANDARD||MATERIAL||OD / INCH||OD / MM||WT / INCH||WT / MM|
|A 270 BPE||304||3/4''||19.05||0.065||1.65|
|A 270 BPE||304||21/2''||63.50||0.065||1.65|
|A 270 BPE||304||6''||152.40||0.109||2.77|
|A 270 BPE||304||8''||203.20||0.109||2.77|
|A 270 BPE||316L||1/2''||12.70||0.065||1.65|
|A 270 BPE||316L||1''||25.40||0.065||1.65|